Introduction
When I first started working in this industry, it took me three hours to bend a single piece of tubing. After that, my boss showed me how to use the Pines #4B Bender tooling on our machine and suddenly my job was much easier and faster.
The Tube Bender Tooling you have makes all the difference in the world.
As a tube bender, you know that the right tools make all the difference in the world. You’ve probably had your fair share of bad tools and maybe even some good ones that came with small problems or quirks that made them less than ideal for your needs.
The wrong tooling will make your life harder and slower. The right tooling will make bending faster and easier. It’s important to get this part right before you start working on perfecting your process, because once you’ve built up some muscle memory around a new way of doing things it can be very difficult to change things up again later on down the road when problems arise due to poor decision making during initial training phase (see “Learning Curve” below).
www.benderparts.com www.facebook.com/benderparts
The Pines #4B Bender is the one tool that your Boss can BEND.
The Pines #4B Bender is the one tool that your Boss can BEND.
It’s not just a bender, it’s an easy-to-use, reliable tool that delivers the results you need in a compact, lightweight package. The Pines #4B Bender is designed to bend tubing up to 1 1/2″ OD and 2″ ID using standard brass blanks or our own custom made, high quality brass and stainless steel blanks. The Pines #4B Bender has been carefully engineered using state of the art technology in order to deliver precision bends every time with minimal effort required on your part.
With the right tooling, you can bend tubing with a tight Bend radius and not crush or collapse your tube.
A tight bend radius is the distance from the center of the bend to the outside of it.
If you don’t have access to tools that can handle a tight radius, your tube will collapse or crush when you try to bend it.
The Ultimate in Tube Bender Tooling is what I get asked for all day long.
If you’re looking for the best tube bender tooling, I get asked about it all day. The Pines Hydraulic #4B Bender is THE professional’s choice because it has all of the features that make a hydraulic tube bender work well:
Works with any tubing diameter (1/2″ to 1″) and wall thickness – from flat stock to .250″ wall.
Accommodates long lengths of tubing without having to move or remove an intermediate piece of pipe.
Has a range of bend angles from 90° up at an adjustable speed of 1-1/2 inches per minute; this means no slowdowns in production when you need to bend thicker material or faster!
www.benderparts.com www.facebook.com/benderparts
If you own a Pines Hydraulic Tube Bender, then you know what I mean when I say that it’s going to take more than just the right machine to get your job done in a decent amount of time.
If you own a Pines Hydraulic Tube Bender, then you know what I mean when I say that it’s going to take more than just the right machine to get your job done in a decent amount of time.
You need the right tool for each task as well. However, let’s be real here: tools aren’t cheap. They’re also not cheap when it comes to shipping and handling either! So what do we do?
Tubing bending doesn’t have to be hard work if your bender has great tooling.
I’m always asked about the tube bender I use, and it’s no surprise. The Pines Hydraulic Tube Bender has a great set of tooling that makes bending all kinds of tubes easier, faster and more accurate.
The Pines Hydraulic Tube Bender uses a 4-way swivel head which allows you to bend in all directions at once. This means that you can bend 1/2″ O.D tubing with precision in just four seconds!
If you’re looking to increase your production rate while still maintaining accuracy, this is one of the best tools out there for this purpose. A good tube bender doesn’t have to cost an arm and a leg either; some brands are even priced under $1k!
www.benderparts.com www.facebook.com/benderparts
If you’re looking for a replacement part for your Pines Hydraulic #4B Bender, but aren’t sure where to start then give me a call at 863-370-6712.
If you’re looking for a replacement part for your Pines Hydraulic #4B Bender, but aren’t sure where to start then give me a call at 863-370-6712. I can help with all things Pines Hydraulic #4B Bender and we can help get you back on track!
You can make your Tube Bending life much easier and faster when you use the right tool on the right machine.
The Pines #4B Bender is the best tool for the job. It’s a professional tool, an investment in your business and a time saver.
The Pines #4B Bender
Is designed to do the job better than any other bender on the market
Is built to last and designed to save you money by eliminating downtime due to malfunctioning or worn out parts
Will increase productivity by reducing setup time
www.benderparts.com www.facebook.com/benderparts
Conclusion
The tube bender tooling I use on a daily basis allows me to get my job done quickly and efficiently. The Pines Hydraulic #4B Bender is one of the best tools in my arsenal, but it’s only as good as the tooling that goes along with it. If you need help finding replacement parts for your bender or if you just want some advice on how to make bending easier for yourself then give me a call at 863-370-6712
www.benderparts.com www.facebook.com/benderparts
#Pinesbender #pines4hydraulictubebender #tubebender #tubebenderrebuilding #pinesbenderparts #ultimatetubebenderparts #tubebending #TUBEBENDERDAVE #pinestubebender